taiswipimad1974.github.io

DWG to PCF.pc3: The plotter configuration cannot be used for one of these reasons: the driver cannot be found, the device cannnot be found, or the driver has a problem. So therefore it doesnt allow me to plot to black and white PDF. Use PLOT command and choose DWG to PDF pc3 printer to print the drawing and we get the file printed in the PDF format. These methods work in AutoCAD 2010 and higher versions and creates PDFs with a vector resolution of 600 DPI which can give us sharp prints in commonly used paper sizes.

AutoCAD Print / Plot :: KIP 3100 With 2011 Heidi Driver Crashes Upon Plot Preview

AutoCAD Architecture 2011
Windows 7 x64
8GB RAM
Created new PC3 for KIP 3100 plotter using its AutoCAD Heidi driver for Win7x64. Upon plot preview the following error occurs.
This causes a crash report which has been submitted to Autodesk. The response was to install service pack 2. Error still occurs after installing the service pack.
Using the non-AutoCAD driver works.

AutoCAD Print / Plot :: Scriptpro 2.0 Not Printing With DWG To PDF Driver

I having difficulty batch printing using Scriptpro 2.0. In short, scriptpro is using the simple batch file (see below), to add a xref and then printing using the DWG to PDF driver. I have tried using a paper printer, which works fine, so I suspect the problem is when scrippro calls the DWG to PDF driver.
I am using accoreconsole.exe application.
I inserted a 'qsave' command after the xref is inserted, and the xref does get saved, so, I know the script is working up to that point.
Batch.scr
Filedia
0
Proxynotice
0
Frame
1
Frame
[code]..

AutoCAD Print / Plot :: Margins On HP LaserJet With HP Universal Driver

Ever since updating our print server to use the HP Universal driver, my ability to tweak the non-printable margins has gone away. In the past I was always able to easily tweak margins within my PC3 files using the 'Modify Standard Paper Sizes (Printable Area)' tool. Setting all four values to say '0.25' would result in an even 1/4' margin around all four edges of the paper.
Now however, that behavior is just plain different. Using 0.25 all the way around results in plots that are partially shifted off the page. Using different values for top, bottom, left and right results in one or two margins coming out much wider than I want. The frustrating part is there seems to be no rhyme or reason between these values and the plot output. The default values are 0.17 for Top/Bottom and 0.25 for Left/Right but even this results in uneven margins. Only if I make the slightest of tweaks can I get any tiny bit of improvement, which is still not up to previous standards. Anything larger and the output is much worse. I've tried all 0.0, setting top/bot only. left/right only, but none of my combinations of values works.
On top of that there seems to be inconsistency between each printer, even when the printer Model is the same. For example the output on my 9050DN printers range from just 'Decent but not like before' to plain 'awful'. My older 8150 DN models look the best but still do not match previous output.
Is there an alternative way to adjust paper margins? Is there a new method to adjusting the 'Modify Standard Paper Sizes (Printable Area)' ?

AutoCAD Print / Plot :: Print / Plot Preview Shows Section Of Drawing

I'm using autocad 2000 and I have a problem printing & plotting. The print, plot preview only shows a section of the drawing. What settings do I need to change for the entire drawing to print for the paper size I need.

Windows 7 Ultimate Overview [Sp1 32-bit] WINDOWS 7 ULTIMATE software is developed by Microsoft and compatibles for windows Operating Systems. /windows-7-ultimate-64-bit-deutsch-rapidshare-downloader.html. They develops software’s for windows OS.

AutoCAD Print / Plot :: Change Plot Setup To Multiple Sheets For Use With Batch Plot

I have one drawing per file at model tab. When I need to plot a multiple page file, I use:
Print > Batch Plot.
The problem is that I have to set plot configurations ( plot style table, plot area, paper size, etc) in each file before use Batch Plot.
Now I received 722 files with a wrong Plot Style Table. For this time I change the associated *.ctb file at Plot Style folder, but I will need to associate the right *.ctb to each drawing. It's also common to have to change other properties.

AutoCAD 2013 :: Video Card Driver Update

I'm updating drivers for Computers with Nividia Quadro 4000 video cards. I went to the Nvidia website and found two drivers. one I found that was certified for AUTOCAD 2013 and the version is 310.50. And another driver for the video card version is 311.50. should i download the newest version or the ACAD Certified version? Could the 'Certified' version download not be current? Are there any drawbacks from one to the other?

Photoshop :: Blue Colors Are Messed Up After Video Driver Update

I just updated my Catalyst to 13.1 and now here is how some of my blues look like: [URL].. how to fix this besides rolling back the driver?

AutoCAD Print / Plot :: Mac Doesn't Allow For Proper Printing On Their Plot Style Setting

I am a Mac user and new to AutoCAD. I am enrolled in a CAD class this semester and the instructor for my session is requiring Windows. Supposedly this is because AutoCAD for Mac does not allow for proper printing on their plot style setting.
I understand that I can install Bootcamp and Windows on my computer, but I'd really like to avoid that if I can. If I were to do my work on my Mac and then digitally transfer my files to a PC for printing purposes, would my files become corrupted or compromised in any way?

AutoCAD Print / Plot :: Sharing Plot Files 64bit With 32bit Machine?

Can users with a 64 bit computer share pc3's and pmp's with 32 bit users without adverse effects?

AutoCAD Print / Plot :: Publish To DWFx Plot Stamp Layer

When I publish a drawing as a multipage DWFx (or PDF for that matter) with 'Include Layer Information' selected, the Plot Stamp (Simple Date/Time and Text) comes out but on different layers on different layouts.
Example:
First Layout : Plotstamp resides on Layer 0
Second Layout: Plotstamp resides on Layer 3P
Third Layout: EQPT-VC
etc
Some general information:
Autodesk AutoCAD 2011 64bit
Autodesk DesignReview - 2012
Adobe Acrobat X Professional
Layer 0 Is thawed/plotable and on in all layouts, viewports all layers, viewports. It has at least one entity per layout
Is there anyway to rectify this and still use the built-in Plot Stamp?

AutoCAD Print / Plot :: 2007 Not Reading Plot Styles Correctly

So the firm I work at has AutoCAD 2000 and 2007. 2000 is installed on 5 out of the 7 computers, and 2007 installed on 6 of the 7 computers. 2 of the computers running just ACAD 2007 are Windows Vista, while all the other computers are Windows XP. We have an OCE TDS320 CAD Printer, an HP Wide Format Printer and a Panasonic 330 Copier/Fax/Printer. Our Problem is that When you try to plot an ACAD2007 drawing it will only plot it in color. This problem did not exist before 1/12/12.
When I select the Plot Style to print I select 'monochrome.stb' which has always worked, now all of a sudden it doesnt. The only way i have found to fix this problem is to change my drawing to layer '0' which is white, so when it tries to print in color it will print black. Another Guy in the firm i work at has ACAD2007 on his computer running XP, he also has 2000 running on the same computer. When he tries to plot on ACAD2007 the same thing happens, so it is not isolated to my computer.
There is a difference though between his Plot Styles on his computer and the ones on mine. His end with .ctb, which works. It only doesnt work when he tries to print a drawing i made off of my computer. Because of this we copied his Plot Style folder for AutoCAD 2007 and installed it into the folder with all of my plot styles on my computer, replacing the '.stb' with '.ctb' That did not work at all. The last thing we tried was to copy over a file that plotted correctly, delete the drawing and draw what we needed, This also did not work. So basically we are thinking that ACAD2007 is not reading the Plot Styles correctly, or the Plot Styles are wrong or currupt.

AutoCAD Print / Plot :: Plot Results From Paperspace Are Different From Model Space?

I have several objects on various layers in model space and they are exposed through a viewport in a paperspace layout. I also have a corporate CTB plot style.
Here is my problem: If i plot the objects from model space, they all plot with the correct lineweights as defined in our corporate CTB, but when i plot them from the paperspace layout, some but not all objects plot with a heavier lineweight than what is defined in the CTB.
I thought the CTB was supposed to override any settings applied to individual objects, but more importantly, why the different results, on the same objects, depending upon the space from which they're plotted?

AutoCAD Print / Plot :: Publish Vs Plot - Image Shifts And Border Cut Off

I have found that when I Publish, the drawing comes out shifted about 1/8' down and 1/8' left as compared to when I use Plot. Which of course is just enough to cut off the sheet border which is 1/2' from the paper edge. I am using the same Page Setup for both Publish and Plot, same drawing.
This is to an Oce TDS600, and it only happens with 15x21 paper size. All paper sizes are set to 0' border. Probably an Oce issue, but have any of you seen this before?

AutoCAD Print / Plot :: Poor Plot Quality With Aerial In 2012?

I recently upgraded from 2010 to 2012 and when trying to plot, using the very same page setups as before the upgrade, the quality (or resolution) of the plot is very poor and pixelated. I am using very high resolution aerial imagery. The output is not at all high resolution (totally pixelated, not presentable as professional). It seems like AutoCAD is reducing the image quality now. Is this a system variable that can be adjusted?

AutoCAD Print / Plot :: Cannot Choose Plotter In Plot Manager

In AutoCAD 2014 and ASD2013 I cannot choose one of the printer, which is installed on Windows (OCE TDS600). It is strange, because Autocad sees it on the list of available plotters, but when I try to select it - it automaticly changes to 'None'.
The plotter is properly configured - I can print with it from Revit 2013 without any problems. Also when I switch account to any other (on that same computer) everything works fine.
I tried to add this plotter through 'Add-A-Plotter Wizard', but each time I obtain an error massage 'Autodesk Hardcopy component failed..'
[URL]

AutoCAD Print / Plot :: DWG To PDF - Lines Plot As Gray Instead Of Black?

Unfortunately I am using ACAD 2000 so bear with me and the only ACAD training I have is a 3 day crash course at the local software reseller.
I am attempting to plot a drawing that was created from a template into a .pdf but it is plotting colored lines instead of black lines.
Here is some background info. My template is set up as a .dwt which I will save as a .dwg when I begin to make my drawings. Plot style table is “monochrome.stb” and I have selected Adobe .pdf as my plotter configuration. I then select the “Properties” then go to “Custom Properties”, “Paper/Quality” tab and then select “Black & White” as my color.
When I go to plot the drawing as a pdf and do a preview of what I am about to plot, I see that the lines that make up the drawing are a shade of gray in color. All my lineweights in the layers property manager are set to default. I have attached a blank drawing that is based off of my template.

AutoCAD Print / Plot :: 2004 - Set To Plot To File / How To Change

2004 and how to turn 'plot to file' off? Any time they go to plot the plot to file is already set and grayed out. It has been way too long since 2004 and I don't know where to have them look although I assume it is in Options somewhere.

AutoCAD Print / Plot :: Application Terminates When Plot Command Is Given

I'm using autocad 2011 LT License version 5 users & autocad 2012 Lt License Version 5 users.I have got a HP Laserjet 5200 printer, when i give a plot command from one of the workstation having autocad 2012 lt
the application gets terminated automatically every time.This issue is only with a single client having 2012LT all other autocad LT 2012 workstations in the same network plots w/o any complaint.

AutoCAD Print / Plot :: Layers Turned Off Plot Unless They Are Frozen?

I have a user which we just installed Autocad Civil 3D 2014 on his computer that is running on a Windows 7 64-bit OS. However, he has had the same problem with Civil 3D 2011, 2012, and 2013 ever since we took him to 2011 in September 2011. So, it is not something new. It may have been around before then but my companies common practice back then was to freeze layers with a script file before plotting. While attending a class back in 2010 or 2011, he and his group were told to “do not use FREEZE on layers in Civil 3D” since things frozen did not get updated like they would if they were just turned off. So, they have been using the “ON/OFF” commands on all Civil 3D files since then.
Here is the problem:
A drawing, typical of this and other jobs he does, has a title block which is an xref in paper space and the site plan xref in model space. He can turn 'OFF' certain layers from the site plan as viewed from paper space to remove clutter and then go to make a plot. After getting it set up to print and going to the preview the layers he has turned off appear in the preview and if he goes ahead and makes the plot or PDF those layers that were turned off will plot out.
The work-a-round they have been using ever since has been to go back into the file(s) and “FREEZE” the layers that were turned off, make the plots and then go back and “THAW” the layers before ending the drawing.
Things we have tried:
Set Visretain=1
Used the “Publish” command.
Set Layerevalctl=0 or 1
Is there a way to use ON/OFF instead and have the layers NOT plot out? OR, is this something that AutoCAD will not do regardless? Has it always been that way and we have been unaware of it through the past four releases?

AutoCAD Print / Plot :: Delay In Plot Manager Window

I have a network with Windows XP and Windows 7.
Printers: from HP 5000 series to a KIP 3000.
CAD,from 2008 to 2012 versions.ALL of the PCs are having this strange behaviour:Open a drawing, Press File then Plot and.
Scenario 1: if the KIP3000 is online then plotting window comes in few seconds, a normal, decent delay!
Scenario 2: if the KIP 3000 is offline then plotting can be delayed to minutes!!!
Downloaded the drivers from KIP web site, installed and tested, prints fine once the above issue with delay is sorted! I’m guessing that is something built-in CAD, pre-emptive, background checks running for printers status when you attempt to plot to the printer / plotter !

AutoCAD Print / Plot :: How To Adjust Grayscale In 3D Model Plot

I need to plot a drawing with a few plans, which are in 2D but also a 3D model of the intire installation and a few side views, which are side views of the 3D model.When I plot the drawing I am able to get the side views in black and white by taking the following steps:(i got these steps from this post: URL..
- set the visual style (in model space) to hidden or wireframe.
- in the layout you select a viewport that conntains a 3D visualisation and double click in that window to set the visual style to 2D wireframe and also set the viewports shade plot to hidden.
because the plotter is black and white only I see those side views in different shades of grey but the problem is that the difference in grey isn't clear enough (and yellow pipes are hardly visible) and I can't adjust these. When adjusting the .ctb it only affects the 2D views and not the 3D views.
It is possible to change the greyness by changing the color of the diffent pipes that are in the drawing but this is not a desired option by the client.how to alter the shades of grey in 3D visualisations so that not all pipelines look the same .I attached a file of what the plot preview looks like and another of what the actual plot looks like

AutoCAD Print / Plot :: Pixelated Plot Of PDF In File When Printing To PDF

I am plotting a file that has a pdf referenced into it. The quality of the plot is degraded only at the inserted pdf. The rest of the AutoCAD file looks fine. The inserted pdf is a printed AutoCAD file which looks clear and even has embedded layers and linework I can snap to (which seems to indicate that there is vector information present when it is in Autocad.
I have attached an image with 4 zoomed-in screen shots to show what I'm describing.

AutoCAD Print / Plot :: 3D Drawing Won't Plot In Black And White Using CTB

We do most of our drawing in 2D – quaint I know, but that’s the way the office works. On occasion we’ll do something as a solid model to guide a client understand a complex roof or a clearance problem. We started a model for a project we are working on and ended up using it as building elevations.
The problem is with plotting. If I use our standard office CTB (which is set to print as black), I get color printouts no matter what I try. I have tried using an STB and changing all our layer colors to “7” in an attempt to make it print black, but I'm getting extremely undesirable - seemingly random - line weight results.
The client wants the next project done in 3D as well and I’d like to be able to have the elevations look right.

AutoCAD Print / Plot :: Apply Plot Styles To Drawing

Is there a way to apply plot styles and line weights to a dwg file like 'dwf ePlot' does but keeping the results in .dwg format?

AutoCAD Print / Plot :: Can't Plot To HP Officejet Pro K8600 From 2007

I can't plot to my HP 8600 from Acad 2007, the plotter lights blink an error and nothing plots. I can save the dwg as a PDF and print the PDF to it fine. Is there a special plot driver for the 8600 or what am I doing wrong?

AutoCAD Print / Plot :: Arabic Fonts Jumbled After Plot

Arabic Fonts Jumbled in Autocad. When i see in autocad it look very clear, when i see preview also, it is very clear.When i plot drawing, it is coming Fonts Jumbled.

AutoCAD Print / Plot :: Batch Plot To Printer Via Publish

Dwg To Pdf Pc3 Download

Been attempting to batch plot numerous dwg files to a printer via publisher. Has been successful on 2010, however experiencing difficulties in 2012.
Method used
open dwg file
set page set up to that required
save down dwg
print>Batch plot
add rest of dwg files to be plotted
remove all layouts to retain only Model Space
Highlight all dwgs
Select page set up from currently open dwg file
Publish
Result - only active dwg prints

AutoCAD Print / Plot :: Plotting To PDF Drawings Disappear When Go To Plot

So I have the educational version of ACAD 2012 and this is my first time using that version. My model is done and I formatted my layout with a border and the model to scale in the viewport. When I go to plot to PDF, all I see is the border. I've tried fiddling with colors and viewports but neither of those did anything.

AutoCAD Print / Plot :: Can't Plot Correctly To PDF With Transparency Hatch

Can't plot correctly to pdf with transparency hatch. I have several draws with hatch transparency, but when plot do pdf and use dwg to pdf.plot the hatch it´s wrong. See the draws in attachments.
I try to plot to dwf and after plot to pdf use a third part plot pdf like pdf995, arcplot, and others, but the problem its the same.
I use autocad 2012 but the problem it´s the same if I change to 2013 or 2014.

AutoCAD Print / Plot :: Wipeouts Plot Solid Black?

We have two Xerox 6204 Wide Format plotters, one in my office and one in another. When I plot the wipeouts (w/in blocks on layer 0, color 255 which is set to 0 screening) it plots as it should.
When the same file plotted with the same *.ctb file in the other office the Xerox plots same wipeouts come out completely black. (The LaserJet prints are not effected).

You should have DWG to PDF plotter in AutoCAD by default. This is very handy if you need to publish your drawing to PDF format, you don’t need to use separate PDF driver.

However, you may find it’s not available for some reason. The ‘plotter’ is a pc3 file stored in your PC. So if you delete it, then you will loose the plotter.

Creating a PC3 plotter

You can create PC3 plotter by accessing application menu (the big red A button)> Print> Manage Plotters.

It will open Windows Explorer and open the location where your plotters are stored. Double click Add-A-Plotter Wizard to run it.

You will see Add Plotter wizard. Choose my computer to create it on your machine, then click next.

On the next page, you can choose Autodesk ePlot (PDF) as plotter manufacturer. Then choose DWG to PDF as model.

Now you can click next and accept default values for the rest of this wizard. Click finish on the last page to finish creating plotter.

Now you should the DWG to PDF plotter.

Image plotters

Dwg To Pdf.pc3 Driver Download Windows 7

I also use this wizard to create TIFF and TGA plotters to create high resolution images. Plotting drawings to JPEG is often not good enough. You can choose Raster File Formats as manufacturer to create those plotters.